Berthon Spain provides yacht detailing in Palma de Mallorca and Port Ginesta in Barcelona, combining thorough cleaning with surface treatment, polishing and protection. We work with yacht owners, captains and managers to agree the attention each vessel needs, whether preparing for the season, an owner’s arrival or sale. Detailing goes beyond a routine wash-down. It addresses persistent marks, weathered finishes and the smaller areas around fittings that need individual attention.
Exterior detailing starts with removing salt, dirt and surface deposits so the condition underneath can be assessed. This helps distinguish marks that can be cleaned away from deterioration requiring polishing or repair.
Close attention to hatch surrounds, locker channels, fittings and recesses forms part of a thorough detailing brief. These areas can retain grime and cleaning residue even when the surrounding deck looks clean.
The scope is agreed around the yacht’s materials, existing treatments and areas of concern.
Dullness, oxidation and superficial marks can affect the appearance of the hull and superstructure. Where the finish is suitable, compounding and polishing can improve gloss and reduce the visibility of light scratches and scuffs.
The treatment depends on whether the surface is gelcoat or paint, its condition and the nature of the defect. Deeper scratches, damaged coatings and other faults may need separate repair.
Our hull and superstructure polishing service includes cleaning, buffing and the application of a protective finish.
Persistent staining needs a targeted approach. Water spots, mineral deposits and marks around fittings may remain after ordinary washing, particularly where deposits have accumulated over time.
Identifying the affected material and the cause of the mark helps determine a suitable treatment. Surface deposits and permanent changes to a finish can look similar, so the likely outcome should be established before work proceeds.
Stainless steel polishing gives individual attention to rails, stanchions, cleats and other exposed fittings. Work around bases, joins and edges helps achieve a more consistent finish across the metalwork.
Glass and surrounding frames require a different approach. Salt residue and water marks need to be considered alongside any existing coatings, while acrylic glazing must be treated according to its own care requirements.
Teak treatment is planned around the condition of the timber and any previous products applied. The aim is to care for the surface using an appropriate method, without unnecessary abrasion.
Natural teak, synthetic decking and moulded non-slip surfaces require different treatments. Deck care must preserve their practical function as well as improve presentation.
Interior detailing concentrates on materials, finishes and areas that need more attention than a general clean. The brief can identify marks on seating, dirt in seams and creases, residue around handles and trim, and difficult-to-reach edges.
Berthon Spain offers interior cleaning and steam cleaning. The appropriate work depends on the fabric, upholstery or finished surface involved; steam treatment is considered only where suitable.
Tell us about delicate materials, existing damage or previous treatments when discussing the interior. This helps establish the scope and any limitations before work begins.
Protection is considered alongside the preparation beneath it. A protective finish should be selected for the material, its condition and how the yacht is used.
For polished hull and superstructure surfaces, this forms part of planning the work. The team can explain the proposed treatment and how to care for the finish afterwards.
Regular washing remains important between detailing visits, helping prevent salt and dirt from accumulating again.
A useful detailing brief identifies what needs attention and the result you want to achieve. Photographs can help highlight particular concerns, while the yacht’s location and access arrangements affect how the work is organised.
We will discuss the surfaces involved, the proposed treatment and any defects that may require separate repair. This gives owners and captains a clear basis for agreeing the work.
For regular wash-downs and care between visits, see our yacht guardiennage service.
| Area | Yacht detailing tasks | Scope or limitations |
|---|---|---|
| Surface assessment | Identify materials, existing coatings, oxidation, staining and surface defects | Establish achievable results and identify areas requiring repair |
| Test areas | Test stain treatments, compounds and polishing methods | Confirm compatibility before wider application |
| Preparation and masking | Protect adjacent surfaces, trim, fittings and sensitive equipment | Preparation for corrective work |
| Surface decontamination | Remove stubborn contamination, greasy deposits and bonded grime | Treatment must suit the finish |
| Water-spot removal | Treat persistent mineral deposits on compatible surfaces | Etched surfaces may require further correction |
| Rust-stain removal | Treat staining beneath fittings and on surrounding surfaces | Does not repair the source of corrosion |
| Waterline stain removal | Treat persistent discolouration and deposits | Access may require lifting the yacht |
| Exhaust-stain removal | Treat embedded soot, oily marks and exhaust staining | Results depend on the surface and severity |
| Black-streak treatment | Remove persistent runoff staining | Identify the source where practical |
| Adhesive removal | Remove old tape, sticker and protective-film residue | Test compatibility with the underlying finish |
| Gelcoat restoration | Treat oxidation, chalking, fading and dullness | Depends on the condition and remaining material |
| Machine compounding | Correct suitable surface defects using an appropriate compound | Removes a controlled amount of surface material |
| Light scratch and scuff correction | Reduce superficial scratches and transfer marks | Deeper damage requires repair |
| Swirl and hologram removal | Refine marks left by previous polishing | Particularly relevant to dark gloss finishes |
| Finish polishing | Improve gloss, clarity and consistency | Match the process to the surface |
| Localised wet sanding | Level suitable defects before compounding and polishing | Specialist work requiring sufficient material thickness |
| Painted-finish correction | Polish compatible paint systems and address suitable defects | Follow the paint manufacturer’s requirements |
| Matt and satin finish treatment | Remove persistent contamination without changing the finish | Conventional gloss polishing may be unsuitable |
| Wax and sealant application | Prepare surfaces and apply suitable marine protection | Specify the product and surfaces included |
| Ceramic coating preparation | Decontaminate, correct and prepare approved surfaces | Separate specialist scope |
| Ceramic coating application | Apply a compatible coating to agreed surfaces | Requires appropriate application and curing conditions |
| Existing coating treatment | Assess contamination and carry out approved remedial treatment | Follow the coating manufacturer’s instructions |
| Stainless steel restoration | Treat tea staining and superficial discolouration; polish fittings | Pitting and structural corrosion require separate attention |
| Detailed metal polishing | Polish around fitting bases, joints, welds and fasteners | Remove trapped residue after treatment |
| Other metal finishes | Treat suitable aluminium, chrome, brass and bronze surfaces | Anodised, plated and lacquered finishes need specific methods |
| Glass deposit removal | Treat persistent water spots and mineral build-up | Account for existing films and coatings |
| Glass polishing | Correct suitable superficial defects | Specialist assessment required |
| Glass protection | Apply a compatible water-repellent treatment | Confirm suitability for the glazing and its use |
| Clear-plastic restoration | Treat suitable haze and minor marks on acrylic or other clear plastics | Hard coatings and material type may restrict correction |
| Detailed recess cleaning | Deep-clean hatch surrounds, locker channels, hinges and fitting recesses | Part of a defined detailing treatment rather than routine upkeep |
| Teak stain treatment | Address localised discolouration and persistent marks | Avoid unnecessary abrasion |
| Teak brightening | Carry out a suitable brightening treatment | Assess timber condition and previous treatments |
| Teak protection | Apply an agreed sealer or protective treatment | Depends on the owner’s preferred appearance |
| Synthetic-deck stain treatment | Treat persistent marks on synthetic teak, composite or foam decking | Follow the manufacturer’s guidance |
| Non-slip surface treatment | Remove embedded contamination from textured decks | Preserve grip |
| Exterior upholstery deep cleaning | Treat embedded dirt in seating, seams, piping and creases | Match the process to the material |
| Upholstery stain removal | Treat sunscreen, food, drink and other persistent marks | Test colourfastness and compatibility |
| Vinyl restoration and protection | Deep-clean and apply suitable protection | Avoid slippery finishes |
| Fabric protection | Apply a compatible stain- or water-repellent treatment | Confirm suitability for the fabric |
| Canvas stain treatment | Treat persistent staining on covers, biminis and sprayhoods | Assess material and stitching condition |
| Canvas reproofing | Apply an approved water-repellent treatment | Follow the fabric manufacturer’s instructions |
| Clear enclosure restoration | Treat suitable haze and marks on flexible transparent panels | Material-specific products and methods required |
| Interior upholstery extraction | Deep-clean compatible sofas, seating and cushions | Control moisture and drying |
| Targeted steam cleaning | Treat suitable materials and difficult deposits | Unsuitable for some fabrics, adhesives and finishes |
| Leather treatment | Deep-clean, condition and protect compatible leather | Identify the leather type first |
| Carpet and rug restoration | Treat stains and extract embedded dirt | Check fibres, dyes, backing and drying requirements |
| Headlining and panel stain treatment | Address localised marks on suitable materials | Avoid saturating adhesives and backing |
| Interior joinery treatment | Remove persistent residue and apply appropriate finish-care products | Damage through the finish requires repair |
| Stone restoration | Treat staining, polish or seal suitable stone surfaces | May require a stone specialist |
| Hard-floor treatment | Deep-clean and apply compatible restorative or protective treatments | Maintain slip resistance |
| Bathroom surface restoration | Treat persistent limescale, staining and deposits on glass, fittings and compatible surfaces | Protect plating, stone and sealants |
| Tender detailing | Correct finishes, treat staining and protect suitable surfaces | Define separately from routine tender cleaning |
| RIB tube treatment | Deep-clean staining and apply compatible protection | Distinguish tube materials before treatment |
| Final finish inspection | Check gloss, clarity, consistency and remaining defects | Inspect under suitable lighting |
| Polishing-residue removal | Remove compound and protective-product residue from edges, joins and fittings | Essential after corrective work |
| Handover and aftercare | Record results, explain remaining defects and provide treatment-specific care guidance | Set realistic expectations for ongoing care |
